TC HELICON GO XLR Mini Mixer and Audio Interface
Original price was: AED1,050.AED949Current price is: AED949.
-8%
Shure SM7B Cardioid Studio Microphone for Broadcaster
Cardioid studio microphone delivers warm and smooth audio reproduction in close-proximity studio and vocal applications. Features include wide-range frequency response, bass roll off and mid-range control, and internal air suspension shock isolation.
Original price was: AED1,799.AED1,659Current price is: AED1,659.
Guaranteed Safe Checkout
Features & Compatibility
Shure SM7B dynamic microphone has a smooth, flat, wide-range frequency response appropriate for music and speech in all professional audio applications. It features excellent shielding against electromagnetic hum generated by computer monitors, neon lights, and other electrical devices. In addition to its standard windscreen, it also includes the A7WS windscreen for close-talk applications.
The SM7B is an outstanding choice for the following applications:
- Recording Studio—Instrumental and Vocal
- Location Recording
- Motion Picture and Television Scoring
- Television, Talk Shows, and News Desks
- Radio Announcing and Production
- Narration
Mounting Instructions
The SM7B can be mounted on a microphone stand or hung from a boom. It is shipped in the boom mounting configuration. To set up the SM7B in the microphone stand mounting configuration, proceed as follows:
- Remove tightening nuts on the sides.
- Remove the fitted washers, the lock washers, the outer brass washers, and the brass sleeves.
- Slide the bracket off the microphone. Be careful not to lose the washers still on the microphone.
- Invert and rotate the bracket. Slide it back onto the bolts over the brass and plastic washers still on the microphone. The bracket should fit so the XLR connector faces the rear of the microphone, and the Shure logo on the back of the microphone is right-side up.
- Replace the brass sleeves. Be sure they are seated properly within the inner washers.
- Replace the outer brass washers, the lock washers and the fitted washers.
- Replace the tightening nuts and tighten the microphone at the desired angle.
NOTE: If the tightening nuts do not hold the microphone in position, one or both of the brass sleeves may not be properly seated within all the washers.
Boom and Microphone Stand Mounting Configuration
MOUNTING ASSEMBLY – EXPLODED VIEW
Windscreen
Use the standard windscreen for general voice and instrumental applications. Use the supplied A7WS windscreen for close-talk applications, such as voice overs or radio announcements, as it offers maximum protection from plosive breath noise and creates a warmer, more intimate sound.
To install the A7WS, follow these instructions:
- To avoid tearing the windscreen during removal, grip it from the plastic ring and the base and remove by gently pulling and twisting.
- If desired, adhere the supplied velcro strips around the microphone grille, approximately one inch from the base of the grille (as shown) to hold new windscreen in place.
- Install the A7WS windscreen by stretching over the velcro strips, then squeezing at the base of the windscreen to adhere to the velcro. No velcro strip inside the windscreen is needed, as the windscreen itself adheres to the velcro. To remove, grip at the base of the windscreen and pull while twisting.
Specifications
Type
Dynamic (moving coil)
Frequency Response
50 to 20,000Â Hz
Polar Pattern
Cardioid
Output Impedance
150 Ω
Sensitivity
(@ 1 kHz, open circuit voltage)
-59Â dBV/Pa[1] (1.12Â mV)
Hum Pickup
(typical, at 60 Hz, equivalent SPL/mOe)
11Â dB
Polarity
Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3
Net Weight
0.764Â kg (1.69Â lbs)
Housing
Dark gray enamel aluminum and steel case with dark gray foam windscreen.
[1] 1 Pa=94 dB SPL
Typical Frequency Response
Typical Polar Pattern
Internal Connections
Overall Dimensions
Accessories
Furnished Accessories
| Switch Cover Plate for SM7, SM7A and SM7B | RPM602 |
| Large Black Foam Windscreen for SM7, also see RK345 | A7WS |
| 5/8″ to 3/8″ Thread Adapter | 31A1856 |
Optional Accessories
| 25 foot (7.5m) Triple-Flex® Microphone XLR Cable with chrome connectors | C25F |
Replacement Parts
| Cartridge for SM7, SM7A and SM7B | RPM106 |
| Black Windscreen for SM7, SM7A, SM7B, also see A7WS | RK345 |
| Nut and Washer for SM7, SM7A and SM7B Yoke Mount | RPM604 |
Additional information
| Brand |
|---|
Customer Reviews
Related Products
Porodo Gaming True-Wireless Gaming Earbuds
Listen to music, Focus on your game, stay sharp, stylish, and professional all with Wireless Earbuds Music/Game Mode. Tap and hold the right earbud for 2s to switch between Game Mode and Music Mode. It comes with four hours of playtime.
After you touch the right earbud the mode will switch between game mode and music mode. The charging case battery is 300mAh.
Rode Dual-powered professional shotgun microphone
- Dual-powered professional shotgun microphone
- Digitally controlled high-pass filter, high-frequency boost and -10dB pad
- Tightly controlled directional pickup with a clean, crisp sound
- Powered by either P48 phantom power or rechargeable internal battery
- Ideal for use on a boom, on a camera or in the studio
Reviews
There are no reviews yet.